Now that we can sensibly test proposed plane configurations with atomic,
sprites are not broken.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Since we now incrementally test atomic state as we build it, we can
loosen restrictions on what we can do with planes, and let the kernel
tell us whether or not it's OK.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
a0f8276fe8 ("compositor-drm: Disallow overlapping overlay planes") was
a little too pessimistic in rejecting occluded views. Whilst it
correctly prevented overlay planes from occluding each other, it also
prevented overlay planes from occluding the scanout plane.
This is undesirable: the primary/scanout plane is specified to stack
strictly below all overlay planes, so there is no need to reject a plane
from consideration for scanout due to being occluded by an overlay
plane.
Shift the check downwards so it only applies to overlay rather than
scanout planes.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
In the plane-only mode, we try to place every view on a hardware plane,
and fail if we can't do this. This requires a full walk of the scene
graph to come up with a complete configuration in order to be able to
test.
In mixed mode, we know at least some visible views will fail to be
promoted to planes and must be composited via the renderer. In order to
still use some planes where possible, we use atomic modesetting's
test-only mode to incrementally test configurations.
We know that the renderer output will always be visible, and because it
is the renderer, that it will be occupying the scanout plane underneath
everything else. The actual renderer buffer doesn't materialise until
after assign_planes, because it cannot know what to render until then.
However, in order to test whether a configuration is valid, we need the
renderer buffer in the scanout plane. For testing, we fake this by
temporarily stealing the old buffer - if it seems sufficiently
compatible - and placing it in the state we construct. This is used to
test whether or not a renderer buffer will work with the addition of
overlay planes.
Doing this incremental testing will allow us to enable plane usage for
atomic by default, since we know ahead of time that our chosen plane
configuration will work.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Add a new mode, which attempts to construct a scene exclusively using
planes. This is a building block for incrementally testing and
constructing state: in the plane-only mode, we test the state exactly
once, when we have constructed a full set of planes and want to know if
it works or not.
When using the renderer, we need to incrementally test views one by one
to see if they will work on planes, falling back to the renderer if not.
This test is different, since the scanout plane will be occupied by the
renderer's buffer. Testing using the renderer or client buffers may have
completely different characteristics, so we need two passes: first,
constructing a state with only planes and testing if that succeeds,
falling back later to a mixed renderer/plane mode which tests
incrementally.
This implements the first mode, and preferentially attempts to use it.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
This will never work, so don't even try to do it.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
The atomic API can allow us to test state before we apply it, to see if
it will be valid. Use this when we construct a plane configuration, to
see if it has a chance of ever working. If not, we can fail
assign_planes early.
This will be used in later patches to incrementally build state by
proposing and testing potential configurations one at a time.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Return a pointer to the plane state, rather than returning its
underlying weston_plane. This eliminates any ambiguity between placing
client buffers on planes, and placing them through the renderer.
drm_output_propose_state is only concerned with preparing, testing, and
returning DRM state objects. Assigning views to weston_planes only
happens later, inside drm_assign_planes. This makes that split more
clear.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Add support for multiple modes to drm_output_propose_state. Currently we
intend to operate in three modes: planes-only (no renderer buffer,
client buffers in planes only), mixed-mode (promote client buffers to
planes where possible, falling back to the renderer where not), and
renderer-only (no plane usage at all).
We want to use the first (planes-only) mode where possible: it can avoid
us having to allocate buffers for the renderer, and it also gives us the
best chance of the optimal configuration, with no composition. In this
mode, we walk the scene looking at all views, trying to put them in
planes, and failing as soon as we find a view we cannot place in a
plane.
In the second mode, rather than failing, we assign those views which
cannot be on a plane to the renderer, and allow the renderer to
composite them.
In the third mode, planes are not usable, so everything but the cursor
goes to the renderer. We will use this when we cannot use the planes-only
mode (because some views cannot be placed in planes), but also cannot
use the 'mixed' mode because we have no renderer buffer yet. Since we
walk the scene graph from top to bottom, using atomic modesetting we
will determine if planes can be promoted in mixed mode by placing a
renderer buffer at the bottom of the scene, placing a cursor buffer if
applicable, then testing if we can add overlay planes to this mode.
Without a buffer from the renderer, we cannot do these tests, so we push
everything through the renderer and then switch to mixed mode on the
next repaint.
This patch implements the mixed and renderer-only modes (previously
differentiated only by the sprites_are_broken flag), with the
planes-only mode being left for a later patch.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
When the sprites_are_broken variable is set, do not attempt to promote
client surfaces to the scanout plane.
We are currently assuming that every client buffer will be compatible
with the scanout plane, but that is not the case, particularly with more
exotic tiled/compressed buffers. Once we promote the client buffer to
scanout, there is no going back: if the repaint fails, we do not mark
this as failed and go back to repaint through composition.
This permanently removes the ability for scanout bypass when using the
non-atomic path. Future patches lift the restriction when using atomic
modesetting, as we can actually test and ensure that the view is
compatible with scanout.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reported-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
The scanout plane strictly stacks under all overlay planes, and the
cursor plane above. However, the stacking of overlay planes with respect
to each other is undefined.
We can control the stacking order of overlay planes with the zpos
property, though this significantly complicates plane assignment. In the
meantime, simply disallow assigning a view to an overlay, when it
overlaps another view which is already on an overlay. This ensures
stacking order is irrelevant, since the planes never intersect each
other.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
When trying to assign planes, keep track of the areas which are
already occluded, and ignore views which are completely occluded. This
allows us to build a state using planes only, when there are occluded
views which cannot go into a plane behind views which can.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
When we come to assign_planes, try very hard to ignore views which are
only visible on other outputs, rather than forcibly moving them to the
primary plane, which causes damage all round and unnecessary repaints.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Move drm_assign_planes into two functions: one which proposes a plane
configuration, and another which applies that state to the Weston
internal structures. This will be used to try multiple configurations
and see which is supported.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Now that we collect information about which modifiers are supported for
KMS display, and are able to create KMS framebuffers with modifiers,
begin using the modifier-aware GBM API.
Client buffers from dmabuf already store multi-plane and modifier
information into drm_fb. Extend this to drm_fb_get_from_bo(), used for
wl_buffer, cursor, and gbm_surface buffers. wl_buffer buffers should by
convention not require modifiers. Cursor buffers must not require
modifiers, as they should be linear. Prior to this patch, GBM buffers
must have been single-planar, and able to used without explicitly naming
modifiers.
Using gbm_surface_create_with_modifiers allows us to pass the list of
modifiers acceptable to KMS for scanout to GBM, so it can allocate
multi-planar buffers or those which are otherwise only addressible with
modifiers. On platforms supporting and preferring modifiers for scanout,
this means that the gbm_bos we get from our scanout surface need to use
the extended API to query multiple planes, offsets, modifiers, etc.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
The per-plane IN_FORMATS KMS property describes the format/modifier
combinations supported for display on this plane. Read and parse this
format, storing the data in each plane, so we can know which
combinations might work, and which combinations definitely will not
work.
Similarly to f11ec02cad ("compositor-drm: Extract overlay FB import to
helper"), we now use this when considering promoting a view to overlay
planes. If the framebuffer's modifier is definitely not supported by the
plane, we do not attempt to use that plane for that view.
This will also be used in a follow-patch, passing the list of modifiers
to GBM surface allocation to allow it to allocate more optimal buffers.
Signed-off-by: Sergi Granell <xerpi.g.12@gmail.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Add support for the GBM_BO_IMPORT_FD_MODIFIER path, which allows us to
import multi-plane dmabufs, as well as format modifiers.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Fixes: https://gitlab.freedesktop.org/wayland/weston/issues/113
When creating a drm_fb from client (wl_buffer/dmabuf), gbm_surface, or
client buffers, set fb->size to 0. The size member is only used for dumb
buffers, where we mmap the whole buffer, and need the size recorded to
later pass to munmap.
Determining the full size of multi-planar buffers is difficult, as
auxiliary planes are not guaranteed to have a (height*stride)
allocation, e.g. if they are subsampled or if they do not contain pixel
data at all but, e.g., compression information. Single-plane tiled
buffers also often pad the buffer allocation to a multiple of tile
height, making our existing calculation incorrect.
Though it does no harm to record incorrect information, it also does
no good as we never use it; remove it in order to avoid any confusion.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
ARRAY_LENGTH returns a size_t; rather than casting its result to
int so we can compare to our signed index variable, just declare the
index as a compatible type in the first place.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
The DPMS connector property is an enum property in KMS, which made our
property handling complain at startup as we weren't defining its enums.
Fix our definition so we parse the enum values.
The only user of the property is the legacy path, which can continue
using fixed values as those values are part of the KMS ABI. The atomic
path does not need any changes, since atomic uses routing and CRTC
active to determine the connector's power state, rather than a property.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Fixes: https://gitlab.freedesktop.org/wayland/weston/issues/125
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Use the new drmModeAddFB2WithModifiers interface to import buffers with
modifiers.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
We currently do the same thing in two places, and will soon have a
third.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Use the same codepath, which has the added advantage of being able to
import dmabufs.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
... in order to be able to use it from scanout as well.
In doing this, the check for format compatibility is moved from after
selecting a plane to before selecting a plane. If different planes have
disjoint format support, this ensures that we don't reject the view from
all overlay consideration, just because the first plane we found didn't
support its format.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Use the new helper to populate the cursor state as well, with some
special-case handling to account for how we always upload a full-size
BO.
As this now fully takes care of buffer transformations, HiDPI client
cursors work, and we also clip the cursor plane completely to CRTC
bounds.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reported-by: Derek Foreman <derekf@osg.samsung.com>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Fixes: https://gitlab.freedesktop.org/wayland/weston/issues/118
Now that we have a helper to fill the plane state co-ordinates from a
view, use this for the scanout plane.
We now explicitly check that the view fills exactly the fullscreen area
and nothing else. We then use the new helper to fill out the plane state
values, and do further checks against the filled-in co-ordinates, i.e.
that we're not trying to show an offset into the buffer, or to scale the
image.
This now allows cases where the buffer -> surface -> view -> output
transform chain cancels each other out for scaling: previously, we would
never consider a buffer for scanout unless its scale matched the
output's. We now only look at the final result of the buffer -> output
transformation, to check that this does not result in translation or
scaling.
An audit of the error paths found some places where we would leave a
plane state hanging; this makes them all consistent.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
When considering a view for placement into an overlay plane, we
previously checked that the buffer's transform and scale were identical
to the output's, and that there were no transformations applied.
We now use a more consistent set of checks through
drm_plane_state_coords_for_view. This checks the complete transformation
chain, allowing only translation and scaling; at the end, we check if
the total buffer -> surface -> view -> output chain requires scaling or
rotation, and disallow it if so.
This allows scaling in the cases where the transformation chain cancels
itself out to produce a 1:1 buffer -> output pixel scale.
An erroneously disallowed case is where buffer -> view -> output
rotations cancel each other out; we prevent a view from being on an
overlay plane if rotation is involved at all. Fixing this would require
a complete analysis of the overall transformation matrix.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
In our new and improved helper to determine the src/dest values for a
buffer on a given plane, make sure we account for all buffer
transformations, including viewport clipping.
Rather than badly open-coding it ourselves, just use the helper which
does exactly this.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reported-by: Tiago Gomes <tiago.gomes@codethink.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Pull this into a helper function, so we can use it everywhere.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Rather than a hardcoded ARGB8888 -> XRGB8888 translation inside a
GBM-specific helper, just determine whether or not the view is opaque,
and use the generic helpers to implement the format translation.
As a consequence of reordering the calls in
drm_output_prepare_overlay_view(), we move the GBM BO dereference into a
different failure path, before it gets captured by the plane state.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
e2e8013633 fixed the same issue as df573031d0 in a different way.
The latter commit (applied earlier in the upstream tree) adds a variable
to assign_planes to keep track of when we successfully assign a view to
the scanout plane, and doesn't call prepare_scanout_view if we have.
The former commit adds this checking inside prepare_scanout_view: if the
pending output state already has a framebuffer assigned to the scanout
plane, we drop out of prepare_scanout_view early. The picked_scanout
variable inside assign_planes can thus be removed.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Tested-by: Emre Ucan <eucan@de.adit-jv.com>
Since it doesn't write to the parameter, we can make it const.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
The flag bits 19-22 of the connector modes, provide the aspect-ratio
information. This information can be stored in flags bits of the
weston mode structure, so that it can used for setting a mode with a
particular aspect-ratio.
Currently, DRM layer supports aspect-ratio with atomic-modesetting by
default. For legacy modeset path, the user-space needs to set the
drm client cap for aspect-ratio, if it wants aspect-ratio information
in modes.
This patch:
- preserves aspect-ratio flags from kernel video modes and
accommodates it in wayland mode.
- uses aspect-ratio to pick the appropriate mode during modeset.
- changes the mode format in configuration file weston.ini to
accommodate aspect-ratio information as:
WIDTHxHEIGHT@REFRESH-RATE ASPECT-RATIO
The aspect-ratio can take the following values :
4:3, 16:9, 64:27, 256:135.
v2: As per recommendation from Pekka Paalanen, Quentin Glidic,
Daniel Stone, dropped the aspect-ratio info from wayland protocol,
thereby avoiding exposure of aspect-ratio to the client.
v3: As suggested by Pekka Paalanen, added aspect_ratio field to store
aspect-ratio information from the drm. Also added drm client
capability for aspect-ratio, as recommended by Daniel Vetter.
v4: Minor modifications and fixes as suggested by Pekka Paalanen.
v5: Rebased, fixed some styling issues, and added aspect-ratio
information while printing weston_modes.
v6: Moved the man pages changes to a different patch. Minor
reorganization of code as suggested by Pekka Paalanen.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
[Pekka: replace ARRAY_SIZE with ARRAY_LENGTH]
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Some modeline generators put out e.g. +HSync instead of +hsync. Accept
that too since it's not ambigous.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
This will allow the seat to be set by the environment as pam_systemd typically
sets the XDG_SEAT variable
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Allow global control of the pixman shadow buffers. The compositor can
choose whether all output use or do not use a shadow buffer with the
pixman renderer.
The option is added to the end of struct weston_drm_backend_config to
avoid bumping WESTON_DRM_BACKEND_CONFIG_VERSION.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Add a flag to pixman-renderer for initializing the output with a shadow
framebuffer. All backends were getting the shadow implcitly, so all
backends are modified to ask for the shadow explicitly.
Using a shadow buffer is usually beneficial, because read-modify-write
cycles (blending) into a scanout-capable buffer may be very slow. The
scanout framebuffer may also have reduced color depth, making blending
and read-back produce inferior results.
In some use cases though the shadow buffer might be just an extra copy
hurting more than it helps. Whether it helps or hurts depends on the
platform and the workload. Therefore let the backends control whether
pixman-renderer uses a shadow buffer for an output or not.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Pixman-renderer uses a single internal shadow buffer. It is enough to
composite the current damage into shadow, but the copy to hw buffer
needs to include the previous damage because of double-buffering in
DRM-backend.
This patch lets pixman-renderer do exactly that without compositing also
the previous damage on DRM-renderer.
Arguably weston_output should not have field previous_damage to begin
with, because it implies double-buffering, which e.g. EGL does not
guarantee. It would be better for each backend explicitly always provide
any extra damage that should be copied to hw.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Allow cloning up to 4 connectors from the same CRTC. All the
implementation bits support more than one head per output already.
Four is just an arbitary number, small but unlikely to ever be the
limiting factor in cloning since hardware is usually very restricted.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
For the attach on an enabled output to have an effect, we need to go
through drmModeSetCrtc or ATOMIC_ALLOW_MODESET.
v9:
- Add another XXX comment.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
When a head is detached from an enabled output, that output needs to go
through a modeset (drmModeSetCrtc() / ATOMIC_ALLOW_MODESET) so that the
connector is actually removed from the CRTC.
This has not yet been a problem, because an output could only have one
head at a time, and would be automatically disabled on detach. It would
be a problem with clone mode.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
If we are processing a connector that does not have an existing routing,
it is possible we pick a CRTC that was previously routed to a connector
we have not enabled yet. If that happens, the latter connector cannot
preserve its routing.
Check that no other connector we might enable later had this CRTC
before.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
To support shared-CRTC clone mode, the chosen CRTC needs to support
driving all the attached connectors. Replace the old algorithm with a
new one that takes into account all associated connectors.
Ideally it should use possible_clones mask to check which encoders (and
therefore connectors) actually can be in a cloned set. However, the DRM
documentation says about possible_clones and possible_crtcs masks both:
"In reality almost every driver gets this wrong."
- https://01.org/linuxgraphics/gfx-docs/drm/gpu/drm-kms.html#c.drm_encoder
Looking at a target device and its kernel where clone mode is desired,
possible_clones is indeed self-conflicting and would not allow cloning
at all. Therefore the implemented algorithm replaces the checking of
possible_clones with luck. It even goes out of its way to find any CRTC
for a configuration, even if not advertised by the kernel as not
supported.
Libweston would need infrastructure to allow trial-and-error CRTC
allocation: rather than picking one CRTC in advance and do or die, it
should try all available CRTCs one by one. Unfortunately that is not yet
possible, so this patch implements what it can. It is also the DRM
upstream opinion that trial-and-error with ATOMIC_TEST would be the way
to go.
Unlike the old algorithm, the new algorithm prefers routings that were
in place when Weston started instead of when enabling an output. When
you never temporarily disable an output, this makes no difference.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
The head was just zalloc()'d, there is no need to memset it to zero.
If a function fails, it is preferable it leaves the output arguments
untouched.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Rename connector_get_current_mode() because it will be useful for
storing not just the current mode on creating a head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Stop using a head for printing the mode list, because there could be
multiple heads. We already gather the mode list from all heads.
No need to print the connector id here, because it is logged with DRM
heads, and core prints the head names on output enable.
The "built-in" flag seemed dead, because it could only be printed if the
kernel provided no modes. If we want more detailed info on where modes
come from, we would need to inspect mode_info or add new flags to
drm_mode or weston_mode.
Add printing the pixel clock, because that is used by the video mode
duplicate removal code.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
If an output has multiple (cloned) heads, it should be enough for any
head to support backlight control for DRM-backend to expose it.
Inspect all attached heads for backlight control and improve the
logging.
Pick the initial backlight level from whatever happens to be the "first"
head, because it's simple.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
A single list of modes needs to be combined from the mode lists in each
attached head. We could just concatenate the lists, but that might
introduce duplicates. Try to avoid duplicates instead by using partially
fuzzy matching.
When a duplicate is found, try to figure out which is more suitable to
use in place of both. If one has the preferred flag and the other
doesn't, take the preferred one. Otherwise use the one already in the
list.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Previously the log contained one line for EDID data and another line for
the head, and you just had to know they belong together. Make it more
obvious to read by putting both head and EDID info on the same line.
We no longer print EDID data every time it is parsed (on every hotplug
event), but only if it changes. I did take a shortcut here and use
weston_head::device_changed as the print condition which relies on the
compositor clearing it, but a failure to do so just means we print stuff
even if it didn't change.
Head info updates also print the head info and not just the EDID data.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Daniel Stone
Sergi Granell
Ankit Nautiyal
Guido Günther
nerdopolis
Pekka Paalanen