If we are processing a connector that does not have an existing routing,
it is possible we pick a CRTC that was previously routed to a connector
we have not enabled yet. If that happens, the latter connector cannot
preserve its routing.
Check that no other connector we might enable later had this CRTC
before.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
To support shared-CRTC clone mode, the chosen CRTC needs to support
driving all the attached connectors. Replace the old algorithm with a
new one that takes into account all associated connectors.
Ideally it should use possible_clones mask to check which encoders (and
therefore connectors) actually can be in a cloned set. However, the DRM
documentation says about possible_clones and possible_crtcs masks both:
"In reality almost every driver gets this wrong."
- https://01.org/linuxgraphics/gfx-docs/drm/gpu/drm-kms.html#c.drm_encoder
Looking at a target device and its kernel where clone mode is desired,
possible_clones is indeed self-conflicting and would not allow cloning
at all. Therefore the implemented algorithm replaces the checking of
possible_clones with luck. It even goes out of its way to find any CRTC
for a configuration, even if not advertised by the kernel as not
supported.
Libweston would need infrastructure to allow trial-and-error CRTC
allocation: rather than picking one CRTC in advance and do or die, it
should try all available CRTCs one by one. Unfortunately that is not yet
possible, so this patch implements what it can. It is also the DRM
upstream opinion that trial-and-error with ATOMIC_TEST would be the way
to go.
Unlike the old algorithm, the new algorithm prefers routings that were
in place when Weston started instead of when enabling an output. When
you never temporarily disable an output, this makes no difference.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
compositor.c has 'touch', so use 'touch' here as well. It is not a
device to begin with.
Signed-off-by: Louis-Francis Ratté-Boulianne <lfrb@collabora.com>
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
v1 Tested-by: Matt Hoosier <matt.hoosier@gmail.com>
We have weston_seat_{init,release}_{pointer,keyboard,touch}() as the
backend-facing API. There is no need to expose the create/destroy
functions which have been for internal use only for quite a long time.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
v1 Tested-by: Matt Hoosier <matt.hoosier@gmail.com>
If an input device is associated to an output that then gets disabled,
there is no case where associating to a different output would be
correct.
The output association is used for absolute positioned input devices,
and an input device like a touchscreen cannot ever be automatically
valid for more than one possible output - the touchscreen display
device.
Therefore do not automatically reassing implicitly associated input
devices to another output. This removes some log spam on shutdown.
In fact, if there can be more than one output at any time, absolute
input devices must be explicitly configured to associate with the
correct output, or the results are essentially undefined in any case.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
The use case driving this change is a clone mode setup, where the user
is hotplugging or unplugging a cloned touchscreen. Even if the output
and head are force-enabled, the touch device should still follow the
connector connection status. If there is no video signal for the
touchscreen (disconnected connector), then the touch input should be
ignored as well.
When the output is force-enabled, we need to trigger
output_heads_changed from connector status changes. If the head or
output are not force-enabled, the compositor will likely attach and
detach the head as appropriate. In clone mode, the attach or detach
needs to trigger output_heads_changed directly. In other cases, it may
be handled through the output getting enabled or disabled which are
different signals.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Associating input devices with weston_outputs by the output name fails
when one output has several heads. We need to match against head names
instead of output names to be able to find all names.
This fixes touchscreen output association in shared-CRTC clone mode when
outputs or input devices appear or disappear.
Even though notify_output_create() is called only when new outputs
appear, the implementation is prepared to also remove output
associations. This will be handy in the future when this function will
handle also head detaching from an output that remains enabled.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Removing the output association from an evdev_device is more than just
setting the pointer to NULL, one also needs to remove the destroy
listener and flag the destroy listener as unused (notify == NULL).
evdev_device_set_output() can already remove associations, so let it
also handle an assignment to NULL output.
Fix notify_output_destroy() to handle removing an association correctly.
Previously, the listener was left "used", which would mean the next call
to evdev_device_set_output() would have wl_list_remove()'d, accessing
freed memory. This could be triggered by having a touchscreen with a
specified output association, and unplugging then re-plugging the
corresponding output.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
In the future evdev_device_set_output() will start getting called more
often, redundantly. Short-circuit the setting if the chosen output is
already set for an input device. This reduces churn in the logs.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Helps admins ensure the configuration is correct.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
The udev property WL_CALIBRATION is an old way of giving Weston a
touchscreen calibration matrix. It is Weston-specific.
The recommended way of setting up a calibration is to use the udev
property LIBINPUT_CALIBRATION_MATRIX, which libinput will load
automatically and therefore applies to all libinput using display
servers and applications.
The syntax of WL_CALIBRATION and LIBINPUT_CALIBRATION_MATRIX is
different as well: WL_CALIBRATION uses pixels as the translation part
units, which makes the values depend on the output resolution.
LIBINPUT_CALIBRATION_MATRIX on the other hand uses normalized units.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Print a note that calibration got skipped if the input device supports a
calibration matrix but there is no associated output to compute it from.
Helps with debugging touchscreen calibration issues.
The code is reorganized and commented a bit, but this does not change
the behaviour.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Struct 'evdev_device' has field 'devnode' which is initialized to NULL,
never assigned, and finally free()'d. Therefore it is useless.
Remove the dead field.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
The head was just zalloc()'d, there is no need to memset it to zero.
If a function fails, it is preferable it leaves the output arguments
untouched.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Rename connector_get_current_mode() because it will be useful for
storing not just the current mode on creating a head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Stop using a head for printing the mode list, because there could be
multiple heads. We already gather the mode list from all heads.
No need to print the connector id here, because it is logged with DRM
heads, and core prints the head names on output enable.
The "built-in" flag seemed dead, because it could only be printed if the
kernel provided no modes. If we want more detailed info on where modes
come from, we would need to inspect mode_info or add new flags to
drm_mode or weston_mode.
Add printing the pixel clock, because that is used by the video mode
duplicate removal code.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
If an output has multiple (cloned) heads, it should be enough for any
head to support backlight control for DRM-backend to expose it.
Inspect all attached heads for backlight control and improve the
logging.
Pick the initial backlight level from whatever happens to be the "first"
head, because it's simple.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
A single list of modes needs to be combined from the mode lists in each
attached head. We could just concatenate the lists, but that might
introduce duplicates. Try to avoid duplicates instead by using partially
fuzzy matching.
When a duplicate is found, try to figure out which is more suitable to
use in place of both. If one has the preferred flag and the other
doesn't, take the preferred one. Otherwise use the one already in the
list.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Previously the log contained one line for EDID data and another line for
the head, and you just had to know they belong together. Make it more
obvious to read by putting both head and EDID info on the same line.
We no longer print EDID data every time it is parsed (on every hotplug
event), but only if it changes. I did take a shortcut here and use
weston_head::device_changed as the print condition which relies on the
compositor clearing it, but a failure to do so just means we print stuff
even if it didn't change.
Head info updates also print the head info and not just the EDID data.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Fix this function to support more than one head per output.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Fix this function to support more than one head per output.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Fix this function to support more than one head per output.
v9:
- Change { connectors, 0 } to { NULL, 0 } in drmModeSetCrtc() args.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Replace the unused_connectors array by iterating through the head list
instead. A head that is not enabled (attached to an enabled output) is
basically an unused connector.
All connectors regardless of their status have a drm_head. This has the
nice effect that drm_pending_state_apply_atomic() does not need to
re-query the connector properties every time, they can be simply looked
up in the drm_head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
In previous patches, all the appropriate fields from drm_output have
been moved into drm_head, and resource allocation has been moved away
from drm_output creation. It is time to throw the switch: this patch
disconnects the drm_output and drm_head lifetimes.
Previously a drm_output was created for a connected connector and
destroyed on disconnection. A drm_head was tied to the drm_output
lifetime just to accommodate the head-based output configuration API
temporarily.
Now all connectors will get a head created regardless of their
connection status. Heads are created and destroyed as connectors appear
and disappear (MST), not when they get connected or disconnected. This
should allow the compositor to force-enable a disconnected connector.
An "empty" drm_output is created with weston_backend::create_output()
hook. This now follows the intent of the head-based output configuration
API.
On hotplug events, all connectors' information is updated regardless of
their connection status changes. It is theoretically possible for a
monitor to change without going through a disconnected state in between.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Move the initialization of the drm_output mode list to
drm_output_set_mode() time.
Once we stop creating the drm_head with the drm_output, there will not
be a head to get the mode list from at drm_output creation time.
Furthermore, once DRM-backend starts supporting more than one head per
output, the combined mode list to be exposed to clients (and the
compositor?) must be constructed with all heads attached.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
The inherited mode is the video mode on the connector when we have not
yet reconfigured the connector, if set.
Get the inherited mode the moment we create a drm_head, not when we
determine the mode for a drm_output. This way we are sure to read all
inherited modes before we reconfigure a single CRTC. Enabling one output
may grab the CRTC from another connector, overwriting whatever mode that
connector might have had.
The inherited mode is stored in drm_head, where we can keep it for the
lifetime of the head, rather than relying on re-loading it from the
kernel at set_mode() time.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
As these planes are allocated on output enable and freed on output
disable, there cannot be a match in the pending_output_list.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
As CRTC is allocated on output enable and deallocated on output disable,
there cannot be any matches in find-by-crtc from the
pending_output_list.
Remove the loop over pending_output_list as never finding anything by
definition.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
A drm_output needs a CRTC only when it is in use. Allocating a CRTC on
creation of drm_output will reserve the CRTC regardless of whether the
output is actually used or not. This may cause creating other
drm_outputs to fail if there are not enough CRTCs.
Instead, allocate the CRTC on drm_output enable() time. A drm_output
will have a valid CRTC only while it is enabled.
This allows us to create drm_output objects arbitrarily and without a
head assignment, which is required by the head-based output API for the
backends. The assigned heads will be known only at enable() time.
Now drm_output_enable() has to call drmModeGetResources() to be able to
find a suitable CRTC. We might want to cache the resources somewhere,
but that is it topic for another patch.
v4: Force resetting unused CRTCs on fini.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Move the connector related fields from drm_output to the drm_head. A
drm_head represents a connector for now.
The code in drm_head_create() to update connector data, monitor
information, etc. is moved into a new function. This will be useful when
DRM-backend starts creating heads for all connectors regardless of their
connection status and will need to update them on hotplug events.
While incurring the churn to move several fields into struct drm_head,
also refactor out drm_head_assign_connector_info(). This function is
needed later when drm_heads will exist regardless of connected status,
as every hotplug event will need to update the state of all connectors.
At that point we will also start handling connector changes that do not
go through an intermediate disconnected state. This refactoring is
trivial enough to be in this patch to reduce the total amount of changes
to be reviewed.
v6:
- adapt to the new places of updating unused_connectors
- free connector in create_output_for_connector() error path
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Backlight is driven per connector, hence it belongs in struct drm_head.
weston_output::set_backlight() API is remains per output so far. There
is no UI to control backlights per head and adding one would be
difficult for an output that has multiple cloned heads.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Instead of iterating output_list and pending_output_list, iterate
head_list to find outputs whose connectors have been disconnected.
This helps a following patch to move connector fields from drm_output to
drm_head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Making this function not depend on drm_head::output field through
drm_output_find_by_connector() will later allow to remove the
drm_head::output field before removing the unused_connectors array. This
helps keeping the commit more fine-grained.
drm_backend_update_unused_outputs() was only interested in enabled
outputs. The new code is 100% equivalent to the old code. The
difference is that weston_head::output is only set for attached heads. A
connector cannot be in use if it is not attached to an output.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Switch drm_output_find_by_connector() to search for the output by
iterating the compositor's head_list. drm_head_find_by_connector() will
be useful later on its own.
As of "compositor-drm: start migration to head-based output API" the
head list is guaranteed to contain all created drm_outputs through the
automatically created drm_head.
This simplifies the code a little, introduces
drm_head_find_by_connector(), and works towards the eventual removal of
drm_output_find_by_connector().
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Helps debugging.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Move the responsibility of ensuring the head will work in the enabled
output to the backends.
A compositor cannot enable an output without heads, and removing the
last head from an output automatically disables the output, so attaching
a new head to an enabled output is only possible for clone mode.
Backends headless, rdp, and x11 forbid clone mode by not having an
attach_head hook implemented; fbdev and wayland explicitly deny clone
mode. Only the DRM backend is affected by this change and even that not
yet because MAX_CLONED_CONNECTORS is 1 in the DRM backend.
Also ensure a global is created for the head when attached to an enabled
output, and log it.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Support attaching custom data to a weston_output by the traditional
destroy listener / wl_signal_get approach.
Needs a new destroy signal, because user data lifetime should be the
lifetime of the weston_output regradless of its enabled status. The old
destroy signal is for output consumers that only care about enabled
outputs in the system and gets emitted on disable, not on destroy.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
To let users pick an arbitrary name for an output, to be used as e.g. a
configuration key, add API to create an output with a given name. For
the same configuration purpose, add a search function as well.
For the search function to be predictable, forbid creating multiple
outputs with the same name. Previously, creating multiple outputs with
the same name would have needed detatching to create outputs from the
same head, now that is forbidden.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
This will be interesting to see when testing clone mode.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Remove the scaffolding that allowed backends to be converted one by one
to the head-based API. Nothing is using these members anymore.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Hook up the libweston facing head-based output API by introducing struct
drm_head, but leave it as a fake so that members can be migrated in
pieces in follow-up patches.
The DRM backend continues to create an output for each connected
connector only, and during output creation it also creates a drm_head
for it. This allows it to pretend it supports the head-based output API
as long as there is only one head per output ever attached.
create_output callback is fake, it will only look up the existing
drm_output by the head name.
Clones are not yet supported, hence max is defined to 1.
This unfortunately introduces some temporary code that will be revomed
later, but seems to be necessary to avoid a single big patch.
v6:
- add missing drm_head_destroy() call
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Follow the standard pattern used in the headless and x11 backend
migration, but also cater for the two other backend modes: --sprawl or
fullscreen-shell, and --fullscreen.
Stops relying on the implicit weston_output::head.
Unlike other backends, this uses the attach_head hook to do the
required head setup that is not possible to do without an output, but
must be done before weston_output_enable(). This also requires the
detach_head hook for the one case where the user attaches a --fullscreen
head and then detaches it without enabling the output.
It is a little awkward to fully initialize heads as late as attach, but
aside from the --sprawl/fullscreen-shell case, there is not really a way
to know the head properties without creating the parent wl_surface and
configuring it.
Heads/outputs created for parent outputs now have distinct names instead
of all being called "wlparent".
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Add safeguards to make it painfully obvious if we ever get the pairing
of wayland_backend_create_output_surface() and
wayland_backend_destroy_output_surface() wrong. Helps catching bugs.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Follow the standard pattern set by the headless backend which also uses
the the window output API.
Stops relying on the implicit weston_output::head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Implement the head-based output API in this backend, and stop relying on
the implicit weston_output::head.
The split between fbdev_head and fbdev_output is somewhat arbitrary.
There is no hotplug or unplug, and there is always 1:1 relationship.
Struct fbdev_screeninfo could have been split as well, but it would not
have made much difference.
I chose fbdev_output to carry the mmap details (buffer_length is now
duplicated here), and fbdev_head to carry the display parameters and
device node path. The device node identifies the head, similar to a
connector.
The backend init creates a head. The compositor uses it to create an
output. Libweston core attaches the head automatically after creating
the output. The attach hook is a suitable place to set up the video
modes on the output as they are dictated by the head, it would be too
late at enable() time.
v7:
- use name argument instead of hardcoded "fbdev" in
fbdev_output_create()
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Destroying the whole output in reenable would cause list walk
corruption: the loop over output_list in session_notify() is not using
wl_list_for_each_safe so output removal would break it.
Creating a new output is also problematic as it needs the compositor to
configure it, but that probably saved us from another list walk failure:
adding the new output to be list while walking the list, possibly
causing it to be destroyed and re-created ad infinitum.
Instead of a complete destroy/create cycle, just do our internal
disable/enable cycle. That will re-open the fbdev, re-read the
parameters, re-create hw_surface, and reinitialize the renderer output.
A problem with this is if fbdev_set_screen_info() fails. We do read the
new parameters, but we don't communicate them to libweston core or old
clients.
However, it is hard to care: to trigger this path, one needs to
VT-switch to another fbdev app which changes the fbdev parameters. That
is quite difficult as VT-switching has been broken for a good while for
fbdev-backend, at least with logind. Also fbdev_set_screen_info() would
have to fail before one should be able to tell something is wrong.
The real reason behind this patch, though, is the migration to the
head-based output API. Destroying and re-creating an output really does
not fit that design. Destroying and re-creating a head would be better,
but again not testable in the current state.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Follow the starndard patttern as the other backends, headless and x11 in
particular, to stop relying on the implicit weston_output::head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Implement the head-based output API in this backend, and stop relying on
the implicit weston_output::head.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
If the idle_repaint() callback has been scheduled when a weston_output
gets destroyed, the callback will hit use-after-free. I have encountered
this when migrating the wayland backend to the head-based API, using
--sprawl, and closing/disconnecting one of the parent compositor
outputs.
Store the idle_repaint callback source, and destroy it in
weston_output_release(), ensuring we don't get a stale call to
start_repaint_loop later.
Signed-off-by: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Acked-by: Derek Foreman <derekf@osg.samsung.com>
Pekka Paalanen
Louis-Francis Ratté-Boulianne